SPONSORS
2024 ICRBE EXPO |
Results 1 - 30 of 39
13 years ago
Al Sanders
So Im willing to pay as little as possible. How about $50? Whos going to sell it to me? haha
Forum: rodboard 13 years ago
Al Sanders
Steve Zayas Wrote:
-------------------------------------------------------
> A little over 3hundred new with upgrade chuck
Im sorry I didn't mention it is used. Are you saying over 300 used?
Forum: rodboard 13 years ago
Al Sanders
I have an old rod and I do not like the tuff butt. I want to put on Hypalon instead. But when I heat the butt its just melts. Should I use a dremel too and cut straight down then pry it off?
Forum: rodboard 13 years ago
Al Sanders
I am looking to buy a Pac Bay rod wrapper with the upgradded chuck. It looks to be in great condition. What is this thing worth?
Forum: rodboard 14 years ago
Al Sanders
I am looking to get some ideas for a rod that I am having built. I would like red over wraps with white underwraps. I think I recall a few pictures on this site that looked great but can't find them. Does anyone have any?
Forum: rodboard 14 years ago
Al Sanders
OH yea I have done the test and the drag is the same no matter what the lenght of the rod. Just wondering if there was a general theory on the rod building community. How much extra pressure do guides add if any? I have found that rollers add none. What about ring guides?
Forum: rodboard 14 years ago
Al Sanders
Lets say you have a reel and set it at 8lbs of drag. You put it on a 9ft rod and pull line to test the drag, then you put the same reel, same drag setting on a 6ft rod and test the drag. Which rod will test out higher? Or will they both be the same? I am trying to see if rod length effects drag.
Forum: rodboard 14 years ago
Al Sanders
I have a rod that has a cork grip and I wanted to stip it off and redo the handle. How would I go about removing the cork?
Forum: rodboard 14 years ago
Al Sanders
I have a 1/2" hypalon grip that I want to ream out to fit a 1" diameter blank. How hard is it to do?
Forum: rodboard 14 years ago
Al Sanders
Not sure how it happend but my epoxy is set and the grip didnt slide all the way down the bank and butt up against the reel seat. I have a little bit more than 1/16" gap between the seat and the grip. I dont know to remove the grip, anyone have any sugestions?
Forum: rodboard 15 years ago
Al Sanders
I know mudhole sells some kits, but is there anywhere else I can buy parts or a kit?
Forum: rodboard 15 years ago
Al Sanders
Sounds like using a bottle of plastic container causes too much heat and that I am mixing it too much. Is qucik bond and ultimate gel as good as 2 part epoxy?
Forum: rodboard 15 years ago
Al Sanders
This seems like alot for. I have 8 taped on right now and when testin the line hits the blank. Looks like I may have to use 9. Has anyone used this blank before? I am using ALPS heavy duty stainless guides
Forum: rodboard 15 years ago
Al Sanders
Ive been building rods for about 4 years (all light to heacy saltwater) and still the part I hate the most is gluing the grips, hancle, reel seat ect...
I use the flexcoast slow dry epoxy. For a small amount of glue in mix in the small measuring cups. Stir for about 3 minutes. If I need alot of glue I take either the resin and dump it into the harder and mix. I only do this when they are both
Forum: rodboard 15 years ago
Al Sanders
I am trying to put X Wrap over 2 layers of cork tape. How do you guys get it too look nice where the cork meet the reel seat and gimbal? It almost looks like in some pics that the x wrap is nicely curled under the cork. You cant even notice that there is cork
Forum: rodboard 15 years ago
Al Sanders
I recently purchased some x-shrink wrap. I was going to put it over eva foam. I was given double sided tape to put on the grip then the x-tube over it. The tape was very hard to get even & once I shrunk the wrap on it, it made the grip way to wide. How do you guys on the west coast do it? All the rods w/ x-wrap I have seen are the same diameter as the normal hypalon grip and you can’t
Forum: rodboard 15 years ago
Al Sanders
I am looking to do along butt wrap on a rod. All I can do is a diamaond wrap which is getting pretty boring. What else can I do that is not too complicated?
Forum: rodboard 15 years ago
Al Sanders
I am looking to build a split grip spinning rod, 12-25lb line. 7' . I want to use it to cast poppers and plugs for striped bass and bluefish. Any reccomendations? The cheaper the better.
Forum: rodboard 15 years ago
Al Sanders
What I useually do is one wrap then use the epoxy then one more and epoxy. I was just wondering if triple wold be better
Forum: rodboard 15 years ago
Al Sanders
Are you fishing for school size bluefin or giants? I know the giants are around there later this summer. I would find out if you going for 30lb or 500lb fish. I just made a GF765ML for 60lb test with aftco rollers.
Forum: rodboard 15 years ago
Al Sanders
Never used cork before. Just sanded down some cork grips. Do they need sealer on them?
Forum: rodboard 15 years ago
Al Sanders
I wasnt looking to make a living just some extra cash. But buying wholesale kills my profits. Im already just doing it for friends, I dont always charge top dollar. I may build about 25-50 rods a year.
Forum: rodboard |