SPONSORS
2024 ICRBE EXPO |
Dale Clemens blanks
Posted by:
Rick hern
(---.bstnma.fios.verizon.net)
Date: December 11, 2017 12:53PM
Hey Guys,
I just came into a number of old dale Clemens blanks. I have 2 versions of 7' graphite rods with a bit of a spiral finish. I think these may have been made by Shakespeare. No numbers on them. I also have (2) 81-51-03 and (1) 81-71-02. Pretty sure these were made by Lami. I am guessing that "81" is for graphite, the 5 and 7 are length in ft. I would say the 5' blanks are ultralight and the 7'(2pc) is a light FW blank. Anyone have any more info on these? value? Thank you. Rick Re: Dale Clemens blanks
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: December 11, 2017 03:52PM
From the 1989 catalog: 81-51-03 , 5ft. Moderate slow 1/16-1/4 oz. .320 butt- 5/2 tip 7/8 oz. $12.10 81-71-02, 7ft. Moderate 1/4-1/2oz. .563 butt-6 tip 2oz. $24.56 Custom S.O.A. (state of the art high Mod. fiberglass, 15% magnesium, 15% titanium The best fiberglass blanks available, some of our testers thought they were graphite. Ferrules must be wrapped prior to flexing the blank. There you have it from the horse's mouth. Edited 1 time(s). Last edit at 12/11/2017 03:53PM by Lynn Behler. Re: Dale Clemens blanks
Posted by:
Tom Kirkman
(Moderator)
Date: December 11, 2017 04:51PM
Value would be nil, unless you find someone that has a particular affinity or use for them. But they are as good now as they were then. Any value might be in using them.
.......... Re: Dale Clemens blanks
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: December 11, 2017 05:41PM
Tom is correct, a similar Fenwick HMG blank sold for $50 in the same catalog. Re: Dale Clemens blanks
Posted by:
Rick hern
(---.bstnma.fios.verizon.net)
Date: December 11, 2017 05:44PM
Thanks guys. they had me fooled, seemed very similar to Lami graphite. Could you also check this number for a 7' blank - 4-91? Thanks so much. Re: Dale Clemens blanks
Posted by:
Tom Kirkman
(Moderator)
Date: December 11, 2017 05:58PM
Clemens had some blank made for them so even if Lamiglas (or whoever) made them, they might not correspond to the same blanks offered directly by the manufacturer.
................... Re: Dale Clemens blanks
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: December 11, 2017 06:19PM
Clemens graphite blanks went under the name Custom Builder and I think (think!) they were Lamiglas. Rick this -4-91 thing, can you provide any more info? I have 89, 93, 99 catalogs. Re: Dale Clemens blanks
Posted by:
Rick hern
(---.bstnma.fios.verizon.net)
Date: December 12, 2017 09:10AM
No, they may not have been Clemens blanks but were part of a large lot. Thanks for the info.
Pretty sure that Lami made a line of blanks with the same specs as Lami GLB for Clemens. I remember comparing GLB841M with the Clemens version way back and they appeared to be the same blank, less the Lami warranty. Sorry, only registered users may post in this forum.
|