SPONSORS
2024 ICRBE EXPO |
Tacky Perma Gloss
Posted by:
Chris Ritchie
(---.cnrocmta01.res.dyn.suddenlink.net)
Date: April 12, 2017 07:23PM
I have an older rod that needed the guides replaced. While removing the guides (first time) I damaged the finish. I ordered up some Perma Gloss and first applied it using a technique involving a hole cut into some neoprene and slid down the blank. That was messy and the finish was uneven. It ended up being really thin at the butt end, almost non-existent, and thick at the tip. I changed the way I was applying and got more even results, but it was still tacky even after sitting overnight. I removed that and reapplied. After a couple of hours, it's still sticky. Although I am not giving up hope that it will set, is there anything I can do to help it cure if it doesn't take care of itself? Re: Tacky Perma Gloss
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: April 12, 2017 08:51PM
What's the relative humidity where you live, zero? Never heard of Permagloss not setting up within 20-30 min. You either have a bad batch or it has been contaminated with something. Maybe the finish on the old blank is causing the contamination.
Norm Re: Tacky Perma Gloss
Posted by:
Tom Kirkman
(Moderator)
Date: April 12, 2017 08:57PM
Put a tea kettle on and let it steam the room for a few minutes. Or set the rod somewhere the humidity is a bit higher.
............. Re: Tacky Perma Gloss
Posted by:
Michael Danek
(---.mskg.mi.frontiernet.net)
Date: April 12, 2017 09:29PM
Is it possible that the Permagloss is attacking the previous finish on the rod? And the combination of the Permagloss and the damaged finish is remaining tacky? Re: Tacky Perma Gloss
Posted by:
Chris Ritchie
(---.cnrocmta01.res.dyn.suddenlink.net)
Date: April 12, 2017 09:34PM
Norman Miller Wrote:
------------------------------------------------------- > What's the relative humidity where you live, zero? > Never heard of Permagloss not setting up within > 20-30 min. You either have a bad batch or it has > been contaminated with something. Maybe the finish > on the old blank is causing the contamination. > Norm I live in Houston. The humidity stays about 900% most of the time. I suppose it's possible. I felt I did a fairly decent job of getting it cleaned up. I roughed it up with an abrasive pad then wiped it down several times with a lint free cloth and alcohol. Edited 1 time(s). Last edit at 04/12/2017 09:38PM by Chris Ritchie. Re: Tacky Perma Gloss
Posted by:
Chris Ritchie
(---.cnrocmta01.res.dyn.suddenlink.net)
Date: April 12, 2017 09:40PM
Michael Danek Wrote:
------------------------------------------------------- > Is it possible that the Permagloss is attacking > the previous finish on the rod? And the > combination of the Permagloss and the damaged > finish is remaining tacky? I suppose anything is possible. I've got it in the bathroom with a tub full of HOT water. Re: Tacky Perma Gloss
Posted by:
Matthew Pitrowski
(---.lightspeed.milwwi.sbcglobal.net)
Date: April 12, 2017 11:30PM
what type of finish is the original ?? how old is the rod ?? if it is some type of lacquer based finish the PG is probably eating in to it causing the problem it will eventually harden or it might just remain tacky
It does sound like a contamination issue you might have to resort to removing the PG and the under lying finish to get a good result JMHOP The best day to be alive is always tomorrow !! Think out side the box when all else fails !!! Wi. Re: Tacky Perma Gloss
Posted by:
Chris Ritchie
(---.cnrocmta01.res.dyn.suddenlink.net)
Date: April 13, 2017 01:13AM
It seems like the sauna did the trick. Thanks for all the input. Re: Tacky Perma Gloss
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: April 17, 2017 05:44PM
Just for laughs - never use alcohol before a finish -- Sand - Wash - then use a fine scoff pad and clean with a DRY PAPER towel The alcohol may have been the fault It can leave a residue on the surface - The pad will take this of Bill - willierods.com Sorry, only registered users may post in this forum.
|