SPONSORS
2024 ICRBE EXPO |
wall mounted dryer
Posted by:
jack black
(99.196.44.---)
Date: August 24, 2016 04:54PM
ok......i'm lazy. but i also have limited bandwith each month so its easier to ask than search and use it up. i am looking for a rod dryer that mounts on the wall, similiar to the FC pro 4 rod dryer. a single rod dryer is fine. why wall mounted? space. i run finish at a fairly fast speed and want to pop it out and pop it into the dryer and carry on with another. thanks Re: wall mounted dryer
Posted by:
Barry Thomas Sr
(---.hsd1.nj.comcast.net)
Date: August 24, 2016 11:47PM
CRB Vertical Wall Mount 4 Rod Dryer from Mudhole Re: wall mounted dryer
Posted by:
jack black
(99.196.44.---)
Date: August 25, 2016 09:47AM
ok,,,,i guess i wasn't clear. due to limited space, i am looking for a SINGLE ROD dryer. Re: wall mounted dryer
Posted by:
John Cates
(---.sub-70-195-207.myvzw.com)
Date: August 25, 2016 09:56AM
Jack
We could make that for you. Call us 512-858-7742 Flex Coat Company Professional Rod Building Supplies www.flexcoat.com Re: wall mounted dryer
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: August 25, 2016 10:26AM
Jack,
A picture of a drum dryer mounted on a well for space considerations. [www.rodbuilding.org] An example of a conventional rod dryer just mounted on a shelf that is mounted onto a wall by a pair of shelf brackets: [www.rodbuilding.org] Or - using the flex coat 4 rod dryer as an example - make a dryer of your own, with a dryer motor, chuck and a set of two or three two or three wheel rod rests. You can mount the dryer on a piece of extruded aluminum that has slots in it and then use the equivalent of T nuts to secure the rod rests so that they would be adjustable back and forth. Or you could take a 1x4 board and mill a slot down the center with a router and indent the back of the board with a wider shallower slot to accommodate a carriage bolt or two that could be used to secure the base of a rod rest that would be used to support your rod. The dryer motor would be mounted to a stand on the end of the board to hold the chuck and the rod. Spend the money for a commercial unit, or buy pieces and build a dryer yourself. Good luck Re: wall mounted dryer
Posted by:
Lynn Williams
(---.mi.res.rr.com)
Date: August 25, 2016 01:33PM
Jack,
Here's a wall mounted 4 rod dryer similar to FC but single wide, you could use the same concept to make a single rod dryer. All of the support brackets and the motor bracket was made using Plexiglas. The dryer sets out from the wall about 5-1/2 inches. [www.rodbuilding.org] [www.rodbuilding.org] Mud Hole has some different types of single rod dryer also. If you can't find what you need and don't want to make it I would definitely give John a call at Flex Coat. Re: wall mounted dryer
Posted by:
Terry Fude
(---.dhcp.fdul.wi.charter.com)
Date: August 25, 2016 05:04PM
I read this yesterday, and in my email from mudhole today they had 18 new crb products, and 1 was a wall mount dryer, for 4 rods.. Re: wall mounted dryer
Posted by:
Barry Thomas Sr
(---.hsd1.nj.comcast.net)
Date: August 27, 2016 12:47AM
Make a Shelf to hold a Single rod dryer Re: wall mounted dryer
Posted by:
jack black
(99.196.44.---)
Date: August 27, 2016 09:49AM
Barry Thomas Sr Wrote:
------------------------------------------------------- > Make a Shelf to hold a Single rod dryer got 2 shelves already full. want to put the dryer on the wall between the shelves. they are far enough apart it will work. Sorry, only registered users may post in this forum.
|