SPONSORS
2024 ICRBE EXPO |
Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Kerry Burgess
(---.dhcp.embarqhsd.net)
Date: July 04, 2015 06:28PM
Seen a post where some rod builders apply finish at speeds up to 200 rpms. I am currently using a 36 rpm motor and its too slow. But the only motors I have found are Flexcoat and the cost for the 120 rpm is $531 and the 200 rpm is over $600. For you rod builders that use the faster motor, where did you get your motor? I need a source. There has got to be a better price out there. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Jerry Driggers
(---.ec.res.rr.com)
Date: July 04, 2015 07:10PM
If you have a power wrapper, apply your finish on that, then transfer the rod to your dryer. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: July 04, 2015 07:11PM
To start with, your topic is incorrect as a Dryer motor. The 200 RPM is a finishing machine. I would suggest you check with Karen @ Bingham ent, that is where I got mine from. Also it is not just the motor, it is the complete machine with adjustable rollers, and it spans 8' in length. I might also add that it comes with a slip clutch to ease application like tunnels, hook keepers, etc Ron Weber Edited 1 time(s). Last edit at 07/04/2015 07:14PM by Ron Weber. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Jay Dubay
(---.try.wideopenwest.com)
Date: July 05, 2015 09:58AM
If your handy, You could always get a DC12v wallwart and run one of these off it, [www.amazon.com] [www.amazon.com] The speed control if you want it is below, You would have make a PVC chuck for it. Or find an old sewing machine at a resale or re-purpose store for the motor and foot pedal and build from that. Just a thought. Jaa Edited 2 time(s). Last edit at 07/05/2015 10:17AM by Jay Dubay. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Kerry Burgess
(---.dhcp.embarqhsd.net)
Date: July 05, 2015 12:21PM
Thank you for your input. Criticism however, if that's what is was, is unnecessary and rude. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: July 05, 2015 01:20PM
Definitely was not meant as criticism, if it was taken that way, then my apologies. Ron Weber Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: July 05, 2015 03:30PM
High RPM is good to coat the thread faster But 200 RPM to me is a little high
I would also think after finish is on that most lower the rpm to level the finish and let excess drip off Bill - willierods.com Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
Ernest Horvath
(---.rmo.bellsouth.net)
Date: July 05, 2015 06:54PM
Kerry, I use a 66RPM motor from Grainger with a Flex-Coat slip clutch attached to the shaft for a finishing motor. The item number is: 1MBF9, 115 volt. it cost $115.85 plus tax and shipping.
The one I replaced was the same and it lasted over 20 years. There phone number is: 1 800 323 0620. Hope this helps. E.P. Re: Flex Coat 120 RPM/200 RPM Dryer Motor
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: July 05, 2015 06:57PM
Check out an email like Roger Willison He can hook you up with something that will work well for you Bill - willierods.com Sorry, only registered users may post in this forum.
|