SPONSORS
2024 ICRBE EXPO |
converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: March 31, 2015 09:17PM
Hi all,
I have an old 2 piece spinning rod that I want to covert into a 1 piece rod. I am wondering whether I should just epoxy the 2 pieces together, then build up the lower side with thread and epoxy followed by decorative thread work over the joint or should I cut the rod so the 2 pieces (diameter) match and install a ferrel inside the rod? The second method may be easier to cover with thread and epoxy. Any input would be great! Thanks, Jon Re: converting a 2 piece rod into a 1 piece
Posted by:
Tom Kirkman
(Moderator)
Date: March 31, 2015 09:36PM
Or... you could just put it together and not take it apart. Not trying to be smart at your expense, but you don't have to take a 2-piece rod apart.
................ Re: converting a 2 piece rod into a 1 piece
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: March 31, 2015 09:43PM
Thank you Tom
I needed a laugh been a long day Bill - willierods.com Re: converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: March 31, 2015 10:14PM
Good one Tom!???? but I want to put it together with strength and do a decorative wrap over the joint. Re: converting a 2 piece rod into a 1 piece
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: March 31, 2015 10:24PM
Prep the two parts and Like said Glue it together
If you want a better look shape the tip to a taper then glue This way you can run the thread up and over the tip section Bill - willierods.com Re: converting a 2 piece rod into a 1 piece
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: March 31, 2015 10:33PM
Dry Fit the two sections -- first -- To make sure you glue them the way you want them Bill - willierods.com Re: converting a 2 piece rod into a 1 piece
Posted by:
Michael Danek
(---.adr02.mskg.mi.frontiernet.net)
Date: April 01, 2015 07:32AM
If I were to do that I would probably misalign the guides. Re: converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: April 01, 2015 07:35AM
The guides have been removed, so its just a 2 piece blank Re: converting a 2 piece rod into a 1 piece
Posted by:
Tom Kirkman
(Moderator)
Date: April 01, 2015 07:55AM
You can just glue the two sections together and incorporate the tie-off of the decorative wrap as the ferrule reinforcement wrap. But out that far much of a decorative wrap may add weight that will be noticeable.
............... Re: converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: April 01, 2015 08:22AM
I thought about that, but what I want to accomplish is to butt the 2 pieces together so the joint is flush and the taper is smooth. I thought I might use my calipers and cut the butt section of the rod to match exactly with the female section of the tip. Then, use the male end of the piece I cut and insert it into both ends as a Ferrell. Does that make any sense? Re: converting a 2 piece rod into a 1 piece
Posted by:
Tom Kirkman
(Moderator)
Date: April 01, 2015 09:18AM
If you're simply going to oversleeve the rod with a permanent joint just make sure the measurements and tapers are a match. You can do an inner sleeve, but depending on the spigot/plug it won't be quite as strong. But the later might be better if you want to put a wrap on top of it.
............... Re: converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: April 01, 2015 09:29AM
Thanks Tom - I will give it a shot Re: converting a 2 piece rod into a 1 piece
Posted by:
Randolph Ruwe
(---.hsd1.wa.comcast.net)
Date: April 01, 2015 06:19PM
Lets start from the beginning!! What type of ferrule is on the blank now? Tip over butt, or spigot? Either one is easy to do what you wish, but it makes a difference on the advice you receive here. Re: converting a 2 piece rod into a 1 piece
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: April 01, 2015 08:05PM
Randy is right I thought it was a two piece and just glue together Guess ya never know Bill - willierods.com Re: converting a 2 piece rod into a 1 piece
Posted by:
Jon Hood
(---.hsd1.fl.comcast.net)
Date: April 03, 2015 07:58AM
its a tip over butt. Male end on butt section, female on tip section. Re: converting a 2 piece rod into a 1 piece
Posted by:
bill boettcher
(---.nwrknj.fios.verizon.net)
Date: April 03, 2015 05:40PM
if you liked it as a two piece and just want it a one piece prep the pieces and glue together
If you want to get rid of the ferrule to make it look slimmer More work Bill - willierods.com Sorry, only registered users may post in this forum.
|